Skip to main content

.22 Rimfire Garand Parts List

.22 Rimfire Garand Parts List

Readers have asked for a complete parts list for Reid Coffield's recent .22 rimfire Garand project. It is as follows, along with some of the photos from that project.

.22 Rimfire Garand Parts:

1.  Complete M1 Garand stock assembly along with all metal hardware, sling loops, buttplate, etc.


2.  Used Garand barrel


3.  Garand gas cylinder (junk or worn-out parts for the gas assembly are fine as these are not functional)

4.  Garand gas cylinder lock

5.  Garand gas cylinder lock screw

6.  Garand front sight and locking screw


7.  Rear half of a demilled Garand receiver

8.  Complete Garand rear sight assembly

9.  Garand trigger housing (only use the floorplate section)


10.  Front 12 inches or so of a ruined Garand op rod

11.  Ruger 10/22 action assembly, including magazine, barrel "V" block retainer and screws, and takedown screw

12.  .22 barrel liner

13.  Spacer block to be fitted between the gas cylinder and the front sight (individual guns can vary as to how high this spacer block should be)

14.  Web or leather sling

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Recommended Articles

See More Recommendations

Popular Videos

Hornady 6MM Creedmoor

Hornady 6MM Creedmoor

Tom Beckstrand and Neal Emery of Hornady highlight the 6MM Creedmoor ammo.

Pinging Steel At Over A Mile Away

Pinging Steel At Over A Mile Away

Big bore semiauto or a lever gun? We look at the futuristic .450 Bushmaster and how it compares to the tried and true .45-70. ISS Prop House gives us the rundown on the guns used in Enemy at the Gate. We ping steel with a .300 WinMag at over a mile.

The Future Of Special Operations Small Arms

The Future Of Special Operations Small Arms

We're taking a look at what the Army's Elite Units are using for service rifles and what the future of SOCOM sniping looks like.

The Glock 21

The Glock 21

Frank and Tony from Gallery of Guns spice up the Glock test using their non-dominant hands.

See More Popular Videos

Trending Articles

While the 6mm-caliber cartridges that can be considered “great” are few in number, some have long and storied histories.12 Great 6mm Cartridges Ammo

12 Great 6mm Cartridges

Steve Gash - August 20, 2020

While the 6mm-caliber cartridges that can be considered “great” are few in number, some have...

With a 16.25-inch-long barrel, a tritium front sight and an aperture rear sight, Springfield's M1A Tanker chambered in .308 is a handy defensive carbine.Springfield Armory M1A Tanker .308 Review Rifles

Springfield Armory M1A Tanker .308 Review

Joel J. Hutchcroft - August 25, 2020

With a 16.25-inch-long barrel, a tritium front sight and an aperture rear sight, Springfield's...

With three versions, three barrel lengths, and three different finishes from which to choose, the Savage Renegauge is by definition a eumatic alternative for a variety of shooting situations.Savage Renegauge Shotgun Review Shotguns

Savage Renegauge Shotgun Review

Steve Gash - July 13, 2020

With three versions, three barrel lengths, and three different finishes from which to choose,...

The Rossi RB22M .22 WMR bolt-action rifle features a synthetic stock, a crossbolt safety, and a detachable five-round magazine. The rifle comes with scope mount bases installed.Rossi RB22M .22 WMR Rifle Review Rifles

Rossi RB22M .22 WMR Rifle Review

Joel J. Hutchcroft - July 10, 2020

The Rossi RB22M .22 WMR bolt-action rifle features a synthetic stock, a crossbolt safety, and...

See More Trending Articles

More Reloading

Loading light handloads can extend your time afield with your .30-06 rifle.Light Handloads for the .30-06 Reloading

Light Handloads for the .30-06

Allan Jones - February 06, 2020

Loading light handloads can extend your time afield with your .30-06 rifle.

The .350 Legend case is a straight-wall case with a slightly tapered body so that it will reliably feed in a bolt-action or semiautomatic rifle. It's also rimless and headspaces on the case mouth. According to its SAAMI specs, the maximum average pressure (MAP) is 55,000 psi, so unlike similarly shaped pistol cases operating at pressures up to 35,000 psi, .350 Legend cases are more likely to stretch when fired and resized.Reloading the .350 Legend Reloading

Reloading the .350 Legend

Lane Pearce - June 09, 2020

The .350 Legend case is a straight-wall case with a slightly tapered body so that it will...

Because case prep is the most time-consuming step in the handloading process, we say any tool that makes it easier is a bargain.Case Prep Made Easy Reloading

Case Prep Made Easy

Lane Pearce - May 29, 2020

Because case prep is the most time-consuming step in the handloading process, we say any tool...

While the .32 H&R Magnum doesn't get the attention it deserves, plenty of handloading components are currently available.Reloading the .32 Magnum — What to Know Reloading

Reloading the .32 Magnum — What to Know

Lane Pearce - October 15, 2020

While the .32 H&R Magnum doesn't get the attention it deserves, plenty of handloading...

See More Reloading

Magazine Cover

GET THE MAGAZINE Subscribe & Save

Digital Now Included!

SUBSCRIBE NOW

Give a Gift   |   Subscriber Services

PREVIEW THIS MONTH'S ISSUE Arrow

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Phone Icon

Get Digital Access.

All Shooting Times subscribers now have digital access to their magazine content. This means you have the option to read your magazine on most popular phones and tablets.

To get started, click the link below to visit mymagnow.com and learn how to access your digital magazine.

Get Digital Access

Not a Subscriber?
Subscribe Now